... value at a maximum loading condition (70 N). Surface characterization (morphology, chemical composition, and phase composition) of worn specimens was performed using FESEM, EDS, and XRD analytical techniques. The results inferred that the predominant wear mechanism was oxidative and abrasive wear...

... for publication in the J ournal of T ribology . 21 11 2022 03 02 2023 09 02 2023 07 03 2023 nitrogen-doped graphene friction and wear high temperature lubrication mechanism mixed lubrication nano-tribology piston rings wear mechanisms National Natural Science...

... the coefficient of friction (COF) values decreased. Other AMed alloys have similar corrosion and wear mechanisms [ 16 ]. Even if SLM technology can produce near-net shape parts, the surface roughness of SLM titanium alloy cannot meet high precision requirements. Therefore, posttreatment is necessary...

... with graphite contents of 30%, 25%, 20%, and 15%, denoted as CG30, CG25, CG20, and CG15, were prepared as the material of slip ring. A series of friction and wear tests were carried out, and wear topography and friction vibration were measured. With the increase of electric current, the wear mechanism of CG30...

...Munish Kumar Gupta; Recep Demirsöz; Mehmet Erdi Korkmaz; Nimel Sworna Ross The application of stainless steel 420 is noted in various industrial sectors such as aerospace, automobile etc. However, the wear mechanism of stainless steel 420 is greatly affected by the use of 100Cr6 balls due...

... on drilling in the deep space environment. The results prove that the coefficient of friction (CoF) is interrelated with load and wear conditions, where CoFs gradually decrease with load growth in both air and vacuum. When the loads keep increasing, however, the wear mechanisms finally change under the high...

... pieces of flake debris are ground out of the severe plastic deformation caused lamellar stacked surface by high tangential stress until the COF decreases due to the generation of oxidation films and enough ball-like particles on the worn surface. In order to analyze the wear mechanism, the worn...

... chemical behavior abrasion adhesion third bodies wear mechanisms In this work, a flow-induced vibration wear simulation method was used to investigate the fretting wear behavior between the Inconel 690 alloy tube and 304 SS plate in a high-temperature and high-pressure steam/water environment...

... of the commutator. Therefore, brush wear includes both mechanical and electrical wears [ 1 ]. The wear-rate of brushes is one of the most important indicators of performance. The wear mechanism of brushes is very complex because many factors can influence current density, material, sliding speed, contact force...

... of materials. A LAM Hastelloy C22 was prepared by rotating strategy in this study, and the wear mechanism induced by heat treatment was investigated. The microstructural results showed that the columnar structure with the size of 1 ∼ 4 μm and the cellular structures with the size of 0.3 ∼ 1 μm were observed...

... microstructure mechanical properties wear behavior friction sliding surface properties and characterization wear mechanisms In recent years, superalloys with improved mechanical properties have emerged as a new study area in the material science community to address the tradeoff between strength...

...-pair, the wear mechanism changed from abrasion and adhesion at low temperature, to abrasion, adhesion, and tribochemical reaction (oxidation) at medium temperature, and adhesion and tribochemical reaction at high temperature. For composites–WC–Co tribo-pair, the wear mechanism was adhesion...

... of wear mechanism from severe adhesive wear to mild adhesive wear. Email: tajdeena@bitsathy.ac.in 1 Corresponding author. Email: mechmega@gmail.com Email: sivanesh.research@gmail.com Email: wasimmech2@gmail.com Contributed by the Tribology Division of ASME for publication in the J...

.../Ti6Al4V (Al 2 O 3 + TiN)/Ti6Al4V AISI304 steel substrate microstructural characterization microhardness wear and friction properties characterization coatings sliding surface layers surface properties and characterization wear mechanisms AISI304 steel is one of the widely used materials...

... 29 07 2022 01 08 2022 29 08 2022 brush seal high-temperature friction high-entropy alloy coating oxygen doping wear mechanisms Natural Science Foundation of Zhejiang Province 10.13039/501100004731 LR20E050001 The brush seal is an important sealing method...

... and characterization wear wear mechanisms References [1] Xiao , X. , Yin , Y. , Bao , J. , Lu , L. , and Feng , X. , 2016 , “ Review on the Friction and Wear of Brake Materials ,” Adv. Mech. Eng. , 8 ( 5 ), p 168781401664730 . 10.1177/1687814016647300 [2] Kumar...

... lubrication elastohydrodynamic lubrication lubricant degradation rolling element bearings rolling fatigue surface fatigue and fretting surface roughness and asperities wear mechanisms References [1] Schatzbe , P. , and Felsen , I. M. , 1968 , “ Effects of Water and Oxygen...

... deformation process. The wear surfaces revealed abrasion and delamination as the predominant wear mechanism, with thermal softening occurring only at the highest applied load and sliding speed. Email: pashamd@student.nitw.ac.in 1 Corresponding author. Email: rnrao@nitw.ac.in Email: syedismail7...

... mechanism is abrasive wear for Cu/316L pairs and plastic deformation for Cu/440C pairs. When the test temperature exceeds 300 °C, the adhesive wear is main wear mechanism. The softening resistance and oxidation process is decisive for the high temperatures tribological behavior. Table 1 The chemical...

... ournal of T ribology . 17 08 2021 19 02 2022 26 02 2022 25 07 2022 electrical plating copper oxide surface finish tribological behavior tin oxide aluminum adhesion coatings contact dry friction surface roughness and asperities surfaces wear wear mechanisms...