The aim of the study was to investigate the friction and wear phenomena of 3 mol % yttria-stabilized tetragonal zirconia polycrystals (3Y-TZP) ceramics with the inclusion of copper oxide (CuO) in large area conformal contact geometry. The pin-on-disk tribometer was used to conduct the dry sliding test using CuO/3Y-TZP as pin and alumina as counter surface. The coefficient of friction (μ) for CuO-added 3Y-TZP was decreased by ∼38% compared to pure 3Y-TZP due to formation of protective tribo film to the substrate. In addition, the experiments also showed that the specific wear rate (k) was reduced by ∼54% with the inclusion of CuO in to 3Y-TZP matrix. The different phases of the zirconia, copper, and yttria as well as the phase transformation before and after sliding test were identified by X-ray diffraction (XRD) analysis. Field emission scanning electron microscopy (FESEM) and energy dispersive X-ray (EDS) analysis revealed the existence of CuO in the patchy layers in the worn-out surface of the tested CuO/3Y-TZP sample leading to lower coefficient of friction and improve the wear resistance against alumina counterface in conformal contact geometry. Severe wear mechanism was the dominating factor due to the local plastic deformation of the large number of asperities since the pair of contact was conformal.
Skip Nav Destination
Article navigation
March 2019
Research-Article
Tribological Influences of CuO Into 3Y-TZP Ceramic Composite in Conformal Contact
Subhrojyoti Mazumder,
Subhrojyoti Mazumder
Materials Processing and
Microsystems Laboratory,
CSIR-Central Mechanical Engineering
Research Institute,
Durgapur 713209, India
Microsystems Laboratory,
CSIR-Central Mechanical Engineering
Research Institute,
Durgapur 713209, India
Search for other works by this author on:
Om Prakash Kumar,
Om Prakash Kumar
Department of Materials
Science and Engineering,
Indian Institute of Technology Patna,
Bihta 801106, Patna, India
Science and Engineering,
Indian Institute of Technology Patna,
Bihta 801106, Patna, India
Search for other works by this author on:
Dinesh Kumar Kotnees,
Dinesh Kumar Kotnees
Department of Materials
Science and Engineering,
Indian Institute of Technology Patna,
Bihta 801106, Patna, India
Science and Engineering,
Indian Institute of Technology Patna,
Bihta 801106, Patna, India
Search for other works by this author on:
Nilrudra Mandal
Nilrudra Mandal
Materials Processing and
Microsystems Laboratory,
CSIR-Central Mechanical Engineering
Research Institute,
Durgapur 713209, India,
e-mail: n_mandal@cmeri.res.in
Microsystems Laboratory,
CSIR-Central Mechanical Engineering
Research Institute,
Durgapur 713209, India,
e-mail: n_mandal@cmeri.res.in
Search for other works by this author on:
Subhrojyoti Mazumder
Materials Processing and
Microsystems Laboratory,
CSIR-Central Mechanical Engineering
Research Institute,
Durgapur 713209, India
Microsystems Laboratory,
CSIR-Central Mechanical Engineering
Research Institute,
Durgapur 713209, India
Om Prakash Kumar
Department of Materials
Science and Engineering,
Indian Institute of Technology Patna,
Bihta 801106, Patna, India
Science and Engineering,
Indian Institute of Technology Patna,
Bihta 801106, Patna, India
Dinesh Kumar Kotnees
Department of Materials
Science and Engineering,
Indian Institute of Technology Patna,
Bihta 801106, Patna, India
Science and Engineering,
Indian Institute of Technology Patna,
Bihta 801106, Patna, India
Nilrudra Mandal
Materials Processing and
Microsystems Laboratory,
CSIR-Central Mechanical Engineering
Research Institute,
Durgapur 713209, India,
e-mail: n_mandal@cmeri.res.in
Microsystems Laboratory,
CSIR-Central Mechanical Engineering
Research Institute,
Durgapur 713209, India,
e-mail: n_mandal@cmeri.res.in
1Corresponding author.
Contributed by the Tribology Division of ASME for publication in the JOURNAL OF TRIBOLOGY. Manuscript received May 21, 2018; final manuscript received October 28, 2018; published online December 6, 2018. Assoc. Editor: Min Zou.
J. Tribol. Mar 2019, 141(3): 031606 (10 pages)
Published Online: December 6, 2018
Article history
Received:
May 21, 2018
Revised:
October 28, 2018
Citation
Mazumder, S., Kumar, O. P., Kotnees, D. K., and Mandal, N. (December 6, 2018). "Tribological Influences of CuO Into 3Y-TZP Ceramic Composite in Conformal Contact." ASME. J. Tribol. March 2019; 141(3): 031606. https://doi.org/10.1115/1.4041894
Download citation file:
Get Email Alerts
Environmentally Friendly MoS2-hBN Solid Lubricants: A Comprehensive Tribological Evaluation
J. Tribol (April 2025)
Machine Learning in Wear Prediction
J. Tribol (April 2025)
Static Characteristics of Hybrid Water-Lubricated Herringbone Groove Journal Bearing
J. Tribol (April 2025)
Related Articles
Nanomechanical and Nanotribological Properties of Carbon, Chromium, and Titanium Carbide Ultrathin Films
J. Tribol (October,2001)
Tribological and Nanomechanical Properties of Unmodified and Crosslinked Ultra-High Molecular Weight Polyethylene for Total Joint Replacements
J. Tribol (April,2004)
Tribological Performances of Modified Babbitt Alloy Under Different Sliding Modes
J. Tribol (June,2021)
Related Proceedings Papers
Related Chapters
Surface Analysis and Tools
Tribology of Mechanical Systems: A Guide to Present and Future Technologies
Wear and Contact Fatigue Properties of a Novel Lubricant Additive
Bearing and Transmission Steels Technology
Understanding the Problem
Design and Application of the Worm Gear