A microstructure design framework for multiscale modeling of wear resistance in bioimplant materials is presented here. The increase in service lifetime of arthroplasty depends on whether we can predict wear resistance and microstructure evolution of a bioimplant material made from ultra high molecular weight polyethylene during processing. Experimental results show that the anisotropy introduced during deformation increases wear resistance in desired directions. After uniaxial compression, wear resistance along the direction, perpendicular to compression direction, increased 3.3 times. Micromechanical models are used to predict microstructure evolution and the improvement in wear resistance during processing. Predicted results agree well with the experimental data. These models may guide the materials designer to optimize processing to achieve better wear behavior along desired directions.
Skip Nav Destination
e-mail: dli@gatech.edu
e-mail: hamid.garmestani@mse.gatech.edu
e-mail: ahzi@imfs.u-strasbg.fr
e-mail: moe.khaleel@pnl.gov
e-mail: david.ruch@tudor.lu
Article navigation
October 2009
Predictive Science And Technology In Mechanics And Materials
Microstructure Design to Improve Wear Resistance in Bioimplant UHMWPE Materials
D. S. Li,
D. S. Li
School of Materials Science and Engineering,
e-mail: dli@gatech.edu
Georgia Institute of Technology
, 771 Ferst Drive, Atlanta, GA 30332-0245
Search for other works by this author on:
H. Garmestani,
H. Garmestani
School of Materials Science and Engineering,
e-mail: hamid.garmestani@mse.gatech.edu
Georgia Institute of Technology
, 771 Ferst Drive, Atlanta, GA 30332-0245
Search for other works by this author on:
S. Ahzi,
S. Ahzi
IMFS,
e-mail: ahzi@imfs.u-strasbg.fr
University of Strasbourg
, 2 Rue Boussingault, 67000 Strasbourg, France
Search for other works by this author on:
M. Khaleel,
M. Khaleel
Computational Science and Mathematics Division,
e-mail: moe.khaleel@pnl.gov
Pacific Northwest National Laboratory
, Richland, WA 99352
Search for other works by this author on:
D. Ruch
e-mail: david.ruch@tudor.lu
D. Ruch
Public Research Centre Henri Tudor
, AMS, 66 rue de Luxembourg, B.P. 144 4002 Esch/Alzette, Luxembourg
Search for other works by this author on:
D. S. Li
School of Materials Science and Engineering,
Georgia Institute of Technology
, 771 Ferst Drive, Atlanta, GA 30332-0245e-mail: dli@gatech.edu
H. Garmestani
School of Materials Science and Engineering,
Georgia Institute of Technology
, 771 Ferst Drive, Atlanta, GA 30332-0245e-mail: hamid.garmestani@mse.gatech.edu
S. Ahzi
IMFS,
University of Strasbourg
, 2 Rue Boussingault, 67000 Strasbourg, Francee-mail: ahzi@imfs.u-strasbg.fr
M. Khaleel
Computational Science and Mathematics Division,
Pacific Northwest National Laboratory
, Richland, WA 99352e-mail: moe.khaleel@pnl.gov
D. Ruch
Public Research Centre Henri Tudor
, AMS, 66 rue de Luxembourg, B.P. 144 4002 Esch/Alzette, Luxembourg
e-mail: david.ruch@tudor.lu
J. Eng. Mater. Technol. Oct 2009, 131(4): 041211 (7 pages)
Published Online: September 3, 2009
Article history
Received:
June 13, 2009
Revised:
June 29, 2009
Published:
September 3, 2009
Citation
Li, D. S., Garmestani, H., Ahzi, S., Khaleel, M., and Ruch, D. (September 3, 2009). "Microstructure Design to Improve Wear Resistance in Bioimplant UHMWPE Materials." ASME. J. Eng. Mater. Technol. October 2009; 131(4): 041211. https://doi.org/10.1115/1.3183786
Download citation file:
Get Email Alerts
Cited By
Modeling Growth and Viscous Flow of Oxide on Cylindrical Silicon Surfaces Including Piezoviscous Inhibition
J. Eng. Mater. Technol (April 2025)
Thermal Conductivity of 3D-Printed Metal Using Extrusion-Based Metal Additive Manufacturing Process
J. Eng. Mater. Technol (April 2025)
Related Articles
Wear Mechanisms of Untreated and Gamma Irradiated Ultra-High Molecular Weight Polyethylene for Total Joint Replacements
J. Tribol (April,2005)
Tribological and Nanomechanical Properties of Unmodified and Crosslinked Ultra-High Molecular Weight Polyethylene for Total Joint Replacements
J. Tribol (April,2004)
Tribological Influences of CuO Into 3Y-TZP Ceramic Composite in Conformal Contact
J. Tribol (March,2019)
Pressure Sensitive Nonassociative Plasticity Model for DRA Composites
J. Eng. Mater. Technol (April,2007)
Related Proceedings Papers
Related Chapters
Wear and Contact Fatigue Properties of a Novel Lubricant Additive
Bearing and Transmission Steels Technology
Understanding the Problem
Design and Application of the Worm Gear
Improvement of Wear Resistance of Steel by Means of a Cavitating Jet and a Submerged Pulse Laser
Proceedings of the 10th International Symposium on Cavitation (CAV2018)