An enhanced model for the dynamic behavior of the peripheral milling process is described. The model predicts the cutting forces and cutter deflections by including the effects of the flank face interference mechanism in addition to the chip removal effects. The interference mechanism is accounted for by considering the flank interference forces to be proportional to the interference volume. The volume of interference is estimated numerically. The total force acting on the tool is a combination of the forces due to the cutting action and forces due to the interference. Experiments performed on 6061-T6 Aluminum validate the simulation results.
Issue Section:
Research Papers
1.
Altintas
Y.
Chan
P. K.
In-Process Detection and Suppression of Chatter in Milling
,” Int. J. of Mach. Tools & Manuf.
, Vol. 32
, 1992
, No. 3
, pp. 329
–347
.2.
DeVor, R. E., Kline, W. A., and Zdeblick, W. J., “A Mechanistic Model for the Force System in End Milling with Application to Machining Airframe Structures,” 8th NAMRC Proc., 1980, pp. 297–303.
3.
Elbestawi
M. A.
Ismail
F.
Du
R.
Ullagaddi
B. C.
Modeling Machining Dynamics Including Damping in the Tool-Workpiece Interface
,” ASME Journal Of Engineering for Industry
, Vol. 116
, 1994
, pp. 435
–439
.4.
Endres
W. J.
DeVor
R. E.
Kapoor
S. G.
A Dual Mechanism Approach to the Prediction of Machining Forces, Part 1: Model Development
,” ASME Journal Of Engineering for Industry
, Vol. 117
, 1995
, pp. 526
–533
.5.
Endres
W. J.
DeVor
R. E.
Kapoor
S. G.
A Dual Mechanism Approach to the Prediction of Machining Forces, Part 2: Model Development
,” ASME Journal Of Engineering for Industry
, Vol. 117
, 1995
, pp. 534
–541
.6.
Kline
W. A.
DeVor
R. E.
Shareef
I. A.
The Prediction of Surface Accuracy in End Milling
,” ASME Journal Of Engineering for Industry
, Vol. 104
, 1982
, pp. 272
–278
.7.
Kline
W. A.
DeVor
R. E.
The Effect of Runout on Cutting Geometry and Forces in End Milling
,” Int. J. Mach. Tool Des. Res.
, Vol. 23
, 1983
, pp. 123
–140
.8.
Martellotti
M.
An Analysis of the Milling Process
,” Transactions of the ASME
, Vol. 63
, 1941
, pp. 677
–700
.9.
Martellotti
M.
An Analysis of the Milling Process, Part II—Down Milling
,” Transactions of the ASME
, Vol. 67
, 1945
, pp. 233
–251
.10.
Merritt
H. E.
Theory of Self-Excited Machine Tool Chatter: Contribution to Machine-Tool Chatter Research
,” ASME Journal Of Engineering for Industry
, Vol. 87
, 1965
, pp. 447
–454
.11.
Montgomery
D.
Altintas
Y.
Mechanism of Cutting force and Surface Generation in Dynamic Milling
,” ASME Journal Of Engineering for Industry
, Vol. 113
, 1991
, pp. 160
–168
.12.
Shaw, M. C., and DeSalvo, G. J., “A New Approach to Plasticity and its Application to Blunt Two Dimensional Indenters,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, May 1970, pp. 469–479.
13.
Smith
S.
Tlusty
J.
Update on High-Speed Milling Dynamics
,” ASME Journal Of Engineering for Industry
, Vol. 112
, 1990
, pp. 142
–149
.14.
Sutherland
J. W.
DeVor
R. E.
An Improved Method for Cutting Force and Surface Error Prediction in Flexible End Milling Systems
,” ASME Journal Of Engineering for Industry
, Vol. 108
, 1986
, pp. 269
–279
.15.
Sutherland, J. W., “A Dynamic Model of the Cutting Force System in the End Milling Process,” Sens. & Cont. for Manuf., PED-Vol. 33, 1988, pp. 53–62.
16.
Tlusty
J.
Dynamics of High Speed Milling
,” ASME Journal Of Engineering for Industry
, Vol. 1
, 1961
, pp. 1
–14
.17.
Tlusty
J.
Ismail
F.
Special Aspects of Chatter in Milling
,” ASME Journal Of Engineering for Industry
, Vol. 105
, 1983
, pp. 24
–32
.18.
Wu
D. W.
A New Approach of Formulating the Transfer Function for Dynamic Cutting Process
,” ASME Journal Of Engineering for Industry
, Vol. 111
, 1989
, pp. 37
–47
.19.
Wu
D. M.
Application of a Comprehensive Dynamic Cutting Force Model to Orthogonal Wave-Generating Processes
,” Int. J. Mech. Sci.
, Vol. 30
, No. 8
, 1988
, pp. 581
–600
.
This content is only available via PDF.
Copyright © 1999
by The American Society of Mechanical Engineers
You do not currently have access to this content.
