Metal mesh foil bearings (MMFBs), simple to construct and inexpensive, are a promising bearing technology for oil-free microturbomachinery operating at high speed and high temperature. Prior research demonstrated the near friction-free operation of a MMFB operating to 60 krpm and showing substantial mechanical energy dissipation characteristics. This paper details further experimental work and reports MMFB rotordynamic force coefficients. The test rig comprises a turbocharger driven shaft and overhung journal onto which a MMFB is installed. A soft elastic support structure akin to a squirrel cage holds the bearing, aiding to its accurate positioning relative to the journal. Two orthogonally positioned shakers excite the test element via stingers. The test bearing comprises a cartridge holding a Copper wire mesh ring, 2.7 mm thick, and a top arcuate foil. The bearing length and inner diameter are 38 mm and 36.5 mm, respectively. Experiments were conducted with no rotation and with journal spinning at 40–50 krpm, with static loads of 22 N and 36 N acting on the bearing. Dynamic load tests spanning frequencies from 150 to 450 Hz were conducted while keeping the amplitude of bearing displacements at 20 µm, 25 µm, and 30 µm. With no journal spinning, the force coefficients represent the bearing elastic structure alone because the journal and bearing are in contact. The direct stiffnesses gradually increase with frequency while the direct damping coefficients drop quickly at low frequencies (< 200 Hz) and level off above this frequency. The damping combines both viscous and material types from the gas film and mesh structure. Journal rotation induces airborne operation with a hydrodynamic gas film separating the rotor from its bearing. Hence, cross-coupled stiffness coefficients appear although with magnitudes lower than those of the direct stiffnesses. The direct stiffnesses, 0.4 to 0.6 MN/m within 200–400 Hz, are slightly lower in magnitude as those obtained without journal rotation, suggesting the air film stiffness is quite high. Bearing direct stiffnesses are inversely proportional to the bearing motion amplitudes, whereas the direct equivalent viscous damping coefficients do not show any noticeable variation. All measurements evidence a test bearing system with material loss factor (γ) ∼ 1.0, indicating significant mechanical energy dissipation ability.
Skip Nav Destination
e-mail: Lsanandres@tamu.edu
Article navigation
December 2011
Research Papers
Metal Mesh Foil Bearing: Effect of Motion Amplitude, Rotor Speed, Static Load, and Excitation Frequency on Force Coefficients
Luis San Andrés,
Luis San Andrés
Mast-Childs Professor
Mechanical Engineering Department,
e-mail: Lsanandres@tamu.edu
Texas A&M University
, College Station, TX 77843-3123
Search for other works by this author on:
Thomas Abraham Chirathadam
Thomas Abraham Chirathadam
Research Assistant
Mechanical Engineering Department,
Texas A&M University
, College Station, TX 77843-3123
Search for other works by this author on:
Luis San Andrés
Mast-Childs Professor
Mechanical Engineering Department,
Texas A&M University
, College Station, TX 77843-3123e-mail: Lsanandres@tamu.edu
Thomas Abraham Chirathadam
Research Assistant
Mechanical Engineering Department,
Texas A&M University
, College Station, TX 77843-3123J. Eng. Gas Turbines Power. Dec 2011, 133(12): 122503 (10 pages)
Published Online: August 29, 2011
Article history
Received:
April 8, 2011
Revised:
April 21, 2011
Online:
August 29, 2011
Published:
August 29, 2011
Citation
San Andrés, L., and Chirathadam, T. A. (August 29, 2011). "Metal Mesh Foil Bearing: Effect of Motion Amplitude, Rotor Speed, Static Load, and Excitation Frequency on Force Coefficients." ASME. J. Eng. Gas Turbines Power. December 2011; 133(12): 122503. https://doi.org/10.1115/1.4004112
Download citation file:
Get Email Alerts
An Experimental Comparison of Methanol Combustion Strategies: Spark Ignition Versus Compression Ignition
J. Eng. Gas Turbines Power
Systems-Based Approach To Predicting Tbc Delamination Due To Cmas Infiltration
J. Eng. Gas Turbines Power
Related Articles
Identification of Rotordynamic Force Coefficients of a Metal Mesh Foil Bearing Using Impact Load Excitations
J. Eng. Gas Turbines Power (November,2011)
Development of a High Speed Gas Bearing Test Rig to Measure Rotordynamic Force Coefficients
J. Eng. Gas Turbines Power (October,2011)
Effects of Mesh Density on Static Load Performance of Metal Mesh Gas Foil Bearings
J. Eng. Gas Turbines Power (January,2012)
A New Analysis Tool Assessment for Rotordynamic Modeling of Gas Foil Bearings
J. Eng. Gas Turbines Power (February,2011)
Related Proceedings Papers
Related Chapters
Summary and Conclusions
Bearing Dynamic Coefficients in Rotordynamics: Computation Methods and Practical Applications
Average Shaft Centerline Plots
Fundamentals of Rotating Machinery Diagnostics
Hydraulic Turbomachines
Mechanical Energy Conversion: Exercises for Scaling Renewable Energy Systems