... is asymmetric, then a unidirectional gas flow can be formed causing so-called EHD gas pumping. In spite of many experiments with different electrode shapes and configurations such as needle-to-mesh, needle-to-ring, wire-to-rod, wire-to-non-parallel plates, etc., aimed at production of intensive gas pumping...

...J. Alex Moreland; Dara W. Childs; Joshua T. Bullock Electric submersible pumps (ESPs) utilize grooved-rotor/smooth-stator (SS/GR) seals to reduce leakage and break up contaminants within the pumped fluid. Additionally, due to their decreased surface area (when compared to a smooth seal), grooved...

...R. Lundgreen; D. Maynes; S. Gorrell; K. Oliphant An inducer is used as the first stage of high suction performance pump. It pressurizes the fluid to delay the onset of cavitation, which can adversely affect performance in a centrifugal pump. In this paper, the performance of a water pump inducer...

... , T. , 2003 , “ Sub-Synchronous Whirl in the LE-7A Rocket Engine Fuel Turbo-Pump ,” Iscorma-2, Poland, pp. 1 – 10 . [13] Hendricks , R. C. , Tam , L. T. , and Muszynska , A. , 2004 , “ Turbomachine Sealing and Secondary Flows, Part 2 – Review of Rotordynamics Issues in Inherently...

...Aydın Hacı Dönmez; Zehra Yumurtacı; Levent Kavurmacıoğlu The aim of the current study is to investigate the effect of inlet blade angles on cavitation performance in a centrifugal pump. In order to reveal this relationship, both hub and shroud blade angles are considered and a two-phase three...

...Ashish Doshi; Salim Channiwala; Punit Singh The larger objective of this research comes from the fact that optimization studies in “pumps operated as turbines” have concentrated only within flow zones without any physical perception regarding the influence of nonflow zones such as back-cavities...

... Pumps RANS simulations Unsteady flows Turbomachines Since few studies focused on the flow dynamics during transient runaway events, no load flow characteristics at steady-state are reviewed in this section. At no load conditions, no torque is produced by the runner and its rotation...

.... Fluids Struct. , 69 , pp. 341 – 354 . 10.1016/j.jfluidstructs.2017.01.004 [11] Botero , F. , Hasmatuchi , V. , Roth , S. , and Farhat , M. , 2014 , “ Non-Intrusive Detection of Rotating Stall in Pump-Turbines ,” Mech. Syst. Signal Process. , 48 ( 1–2 ), pp. 162 – 173 . 10.1016...

...Wang Jian; Wang Yong; Liu Houlin; Si Qiaorui; Matevž Dular Cavitation has bothered the hydraulic machinery for centuries, especially in pumps. It is essential to establish a solid way to predict the unsteady cavitation evolution with considerable accuracy. A novel cavitation model was proposed...

... improvement of engines and thermodynamic cycles for various applications. Computational fluid dynamics Duct Gas dynamics Pumps Unsteady flows Channel Pipe flows Turbomachines 16 05 2017 10 04 2018 Contributed by the Fluids Engineering Division of ASME for publication...

...Xiaolong Fu; Deyou Li; Hongjie Wang; Guanghui Zhang; Zhenggui Li; Xianzhu Wei; Daqing Qin Complex energy conversion and energy dissipation occur in pump-turbines during the load rejection process. However, the underlying fluid mechanism is not clear. In order to solve these problems, in this study...

... 26, 2018; published online May 2, 2018. Assoc. Editor: Devesh Ranjan. 24 10 2017 26 03 2018 Compressible flows Gas dynamics Pumps Shocks Supersonic flows Turbomachines Condensation shocks are encountered in steam nozzles and in blade passages of the last stages...

...Ming Liu; Lei Tan; Shuliang Cao Prewhirl regulation by inlet guide vanes (IGVs) has been proven as an effective method for operation regulation of centrifugal pumps. By contrast, the influence of the geometry of IGVs on operation stability of centrifugal pump remains unknown. The pressure...

...Hyeon-Seok Shim; Kwang-Yong Kim; Young-Seok Choi This work presents a three-objective design optimization of a centrifugal pump impeller to reduce flow recirculation and cavitation using three-dimensional (3D) Reynolds-averaged Navier–Stokes equations. A cavitation model was used to simulate...

...D. G. J. Detert Oude Weme; M. S. van der Schoot; N. P. Kruyt; E. J. J. van der Zijden The effect of trimming of radial impellers on the hydraulic performance of low specific-speed centrifugal pumps is studied. Prediction methods from literature, together with a new prediction method that is based...

...] Dennis , D. J. C. , 2015 , “ Coherent Structures in Wall-Bounded Turbulence ,” An. Acad. Bras. Cienc. , 87 ( 2 ), pp. 1161 – 1193 . 10.1590/0001-3765201520140622 Boundary layers Measurement techniques Pumps Stability Turbulence Fluid mechanics Turbomachines Transition...

...Jinhong Hu; Jiandong Yang; Wei Zeng; Jiebin Yang The transient behaviors of a prototype pump turbine are very important to the safe operation of a pumped-storage power plant. This is because the water hammer pressure during transient events affects the pressure surges in the spiral case (SC...

... , A. , Hayrapetian , V. , Untaroiu , C. D. , Wood , H. G. , Schiavello , B. , and McGuirre , J. , 2013 , “ On the Dynamic Properties of Pump Liquid Seals ,” ASME J. Fluids Eng. , 135 ( 5 ), p. 051104 . 10.1115/1.4023653 [9] Untaroiu , A. , Untaroiu , C. D. , Wood , H. G...

...Grunde Olimstad; Morten Osvoll; Pål Henrik Enger Finstad For low-flow and high-head applications, pump types such as progressive cavity or gear pumps are often used. However, centrifugal pumps are much more robust and wear resistant, and are beneficial if they can handle the rated head and flows...

...Mao Xiuli; Pavesi Giorgio; Zheng Yuan Flexible electricity demand and variability of the electricity produced by wind turbines and photovoltaic affect the stable operations of power grids. Pump-turbines are used to stabilize the power grid by maintaining a real-time electricity demand. Consistently...