A probabilistic approach for model updating and damage detection of structural systems is presented using noisy incomplete input and incomplete response measurements. The situation of incomplete input measurements may be encountered, for example, during low-level ambient vibrations when a structure is instrumented with accelerometers that measure the input ground motion and the structural response at a few instrumented locations but where other excitations, e.g., due to wind, are not measured. The method is an extension of a Bayesian system identification approach developed by the authors. A substructuring approach is used for the parameterization of the mass, damping and stiffness distributions. Damage in a substructure is defined as stiffness reduction established through the observation of a reduction in the values of the various substructure stiffness parameters compared with their initial values corresponding to the undamaged structure. By using the proposed probabilistic methodology, the probability of various damage levels in each substructure can be calculated based on the available dynamic data. Examples using a single-degree-of-freedom oscillator and a 15-story building are considered to demonstrate the proposed approach.
Skip Nav Destination
e-mail: kvyuen@umac.mo
e-mail: jimbeck@caltech.edu
Article navigation
July 2006
Technical Papers
Unified Probabilistic Approach for Model Updating and Damage Detection
Ka-Veng Yuen,
Ka-Veng Yuen
Department of Civil and Environmental Engineering,
e-mail: kvyuen@umac.mo
University of Macau
, Macau, China
Search for other works by this author on:
James L. Beck,
James L. Beck
Division of Engineering and Applied Science,
e-mail: jimbeck@caltech.edu
California Institute of Technology
, Mail Code 104-44, Pasadena, CA 91125
Search for other works by this author on:
Lambros S. Katafygiotis
Lambros S. Katafygiotis
Department of Civil Engineering,
Hong Kong University of Science and Technology
, Clearwater Bay, Kowloon, Hong Kong
Search for other works by this author on:
Ka-Veng Yuen
Department of Civil and Environmental Engineering,
University of Macau
, Macau, Chinae-mail: kvyuen@umac.mo
James L. Beck
Division of Engineering and Applied Science,
California Institute of Technology
, Mail Code 104-44, Pasadena, CA 91125e-mail: jimbeck@caltech.edu
Lambros S. Katafygiotis
Department of Civil Engineering,
Hong Kong University of Science and Technology
, Clearwater Bay, Kowloon, Hong KongJ. Appl. Mech. Jul 2006, 73(4): 555-564 (10 pages)
Published Online: September 29, 2005
Article history
Received:
July 11, 2004
Revised:
September 29, 2005
Citation
Yuen, K., Beck, J. L., and Katafygiotis, L. S. (September 29, 2005). "Unified Probabilistic Approach for Model Updating and Damage Detection." ASME. J. Appl. Mech. July 2006; 73(4): 555–564. https://doi.org/10.1115/1.2150235
Download citation file:
Get Email Alerts
Modeling the Dynamic Response of a Light-Driven Liquid Crystal Elastomer Fiber/Baffle/Spring-Coupled System
J. Appl. Mech (December 2024)
Why Biological Cells Cannot Stay Spherical?
J. Appl. Mech (December 2024)
Programmable Supratransmission in a Mechanical Chain with Tristable Oscillators
J. Appl. Mech (December 2024)
Adhesion of a Rigid Sphere to a Freestanding Elastic Membrane With Pre-Tension
J. Appl. Mech (December 2024)
Related Articles
Random Response Analysis of Preisach Hysteretic Systems With Symmetric Weight Distribution
J. Appl. Mech (March,2002)
An Experimental Study on the Seismic Response of Base-Isolated Secondary Systems
J. Pressure Vessel Technol (February,2002)
Stochastic Averaging of Quasi-Nonintegrable-Hamiltonian Systems Under Poisson White Noise Excitation
J. Appl. Mech (March,2011)
Stochastic Averaging of Strongly Nonlinear Oscillators Under Combined Harmonic and Wide-Band Noise Excitations
J. Vib. Acoust (October,2008)
Related Proceedings Papers
Related Chapters
Use of PSA in Lisencing of EPR 1600 in Finland (PSAM-0160)
Proceedings of the Eighth International Conference on Probabilistic Safety Assessment & Management (PSAM)
Tolerance Stack-Up Analysis
Geometric Dimensioning and Tolerancing Handbook: Applications, Analysis & Measurement
Tolerance Stack-Up Analysis
Geometric Dimensioning and Tolerancing: Applications, Analysis, Gauging and Measurement [per ASME Y14.5-2018]