0


Research Papers

J Biomech Eng. 2019;141(5):051001-051001-6. doi:10.1115/1.4043028.

The study of the knee natural motion, namely the unresisted motion that the knee exhibits in the absence of external loads, provides insights into the physiology of this articulation. The natural motion represents the baseline condition upon which deformations of its passive structures (i.e., ligaments and cartilage) take place when loads are applied. Moreover, during natural motion, the strain energy density stored within ligaments and cartilage is minimized. This reduces the chance of microdamage occurrences and the corresponding metabolic cost for tissue repairing. The study of the knee natural motion is thus fundamental in understanding the joint physiology. This paper shows that the line of action of resultant forces of all the knee constraints provided by the passive structures must intersect the instantaneous helical axis (IHA) to make the knee natural motion possible. In other words, the lines of action of all these constraints must cross the same line at each flexion angle to guarantee the natural motion of the joint. This geometrical property is first proven theoretically and then verified in four in vitro and one in vivo experiments. The geometrical characterization of the knee natural motion presented in this study provides a fundamental property that must be satisfied to allow the correct joint mobility. The knowledge of this property may thus allow the definition of better models, treatments, and devices.

Topics: Knee
Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051002-051002-10. doi:10.1115/1.4042682.

Pulmonary hypertension (PH) is a degenerative disease characterized by progressively increased right ventricular (RV) afterload that leads to ultimate functional decline. Recent observational studies have documented a decrease in left ventricular (LV) torsion during ejection, with preserved LV ejection fraction (EF) in pediatric and adult PH patients. The objective of this study was to develop a computational model of the biventricular heart and use it to evaluate changes in LV torsion mechanics in response to mechanical, structural, and hemodynamic changes in the RV free wall. The heart model revealed that LV torsion and apical rotation were decreased when increasing RV mechanical rigidity and during re-orientation of RV myocardial fibers, both of which have been demonstrated in PH. Furthermore, structural changes to the RV appear to have a notable impact on RV EF, but little influence on LV EF. Finally, RV pressure overload exponentially increased LV myocardial stress. The computational results found in this study are consistent with clinical observations in adult and pediatric PH patients, which reveal a decrease in LV torsion with preserved LV EF. Furthermore, discovered causes of decreased LV torsion are consistent with RV structural adaptations seen in PH rodent studies, which might also explain suspected stress-induced changes in LV myocardial gene and protein expression.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051003-051003-14. doi:10.1115/1.4042898.

Electrosurgical procedures are ubiquitously used in surgery. The commonly used power modes, including the coagulation and blend modes, utilize nonsinusoidal or modulated current waveforms. For the same power setting, the coagulation, blend, and pure cutting modes have different heating and thermal damage outcomes due to the frequency dependence of electrical conductivity of soft hydrated tissues. In this paper, we propose a multiphysics model of soft tissues to account for the effects of multifrequency electrosurgical power modes within the framework of a continuum thermomechanical model based on mixture theory. Electrical and frequency spectrum results from different power modes at low- and high-power settings are presented. Model predictions are compared with in vivo electrosurgical heating experiments on porcine liver tissue. The accuracy of the model in predicting experimentally observed temperature profiles is found to be overall greater when frequency-dependence is included. An Arrhenius type model indicates that more tissue damage is correlated with larger duty cycles in multifrequency modes.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051004-051004-11. doi:10.1115/1.4043029.

Aging and degeneration of the intervertebral disk are noted by changes in tissue composition and geometry, including a decrease in nucleus pulposus (NP) area. The NP centroid is positioned slightly posterior of the disk's centroid, but the effect of NP size and location on disk joint mechanics is not well understood. We evaluated the effect of NP size and centroid location on disk joint mechanics under dual-loading modalities (i.e., compression in combination with axial rotation or bending). A finite element model (FEM) was developed to vary the relative NP area (NP:Disk area ratio range = 0.21–0.60). We also evaluated the effect of NP position by shifting the NP centroid anteriorly and posteriorly. Our results showed that compressive stiffness and average first principal strains increased with NP size. Under axial compression, stresses are distributed from the NP to the annulus, and stresses were redistributed toward the NP with axial rotation. Moreover, peak stresses were greater for disks with a smaller NP area. NP centroid location had a greater impact on intradiscal pressure during flexion and extension, where peak pressures in the posterior annulus under extension was greater for disks with a more posteriorly situated NP. In conclusion, the findings from this study highlight the importance of closely mimicking NP size and location in computational models that aim to understand stress/strain distribution during complex loading and for developing repair strategies that aim to recapitulate the mechanical behavior of healthy disks.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051005-051005-12. doi:10.1115/1.4043037.

Early weight bearing appears to enhance bone fracture healing under Ilizarov circular fixators (ICFs). However, the role of early weight bearing in the healing process remains unclear. This study aims to provide insights into the effects of early weight bearing on healing of bone fractures stabilized with ICFs, with the aid of mathematical modeling. A computational model of fracture site was developed using poro-elastic formulation to simulate the transport of mesenchymal stem cells (MSCs), fibroblasts, chondrocytes, osteoblasts, osteogenic growth factor (OGF), and chondrogenic growth factor (CGF) and MSC differentiation during the early stage of healing, under various combinations of fracture gap sizes (GS), ICF wire pretension forces, and axial loads. 1 h of physiologically relevant cyclic axial loading followed by 23 h of rest in the post-inflammation phase (i.e., callus with granulation tissue) was simulated. The results show that physiologically relevant dynamic loading could significantly enhance cell and growth factor concentrations in the fracture site in a time and spatially dependent manner. 1 h cyclic loading (axial load with amplitude, PA, of 200 N at 1 Hz) increased the content of chondrocytes up to 37% (in all zones of callus), CGF up to 28% (in endosteal and periosteal callus) and OGF up to 50% (in endosteal and cortical callus) by the end of the 24 h period simulated. This suggests that the synergistic effect of dynamic loading-induced advective transport and mechanical stimuli due to early weight bearing is likely to enhance secondary healing. Furthermore, the study suggests that relatively higher PA values or lower ICF wire pretension forces or smaller GS could result in increased chondrocyte and GF content within the callus.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051006-051006-7. doi:10.1115/1.4043035.

Degenerative wear to the glenoid from repetitive loading can reduce effective concavity depth and lead to future instability. Workspace design should consider glenohumeral stability to prevent initial wear. While glenohumeral stability has been previously explored for activities of daily living including push–pull tasks, whether stability is spatially dependent is unexplored. We simulated bimanual and unimanual push–pull tasks to four horizontal targets (planes of elevation: 0 deg, 45 deg, 90 deg, and 135 deg) at 90 deg thoracohumeral elevation and three elevation targets (thoracohumeral elevations: 20 deg, 90 deg, 170 deg) at 90 deg plane of elevation. The 45 deg horizontal target was most stable regardless of exertion type and would be the ideal target placement when considering stability. This target is likely more stable because the applied load acts perpendicular to the glenoid, limiting shear force production. The 135 deg horizontal target was particularly unstable for unimanual pushing (143% less stable than the 45 deg target), and the applied force for this task acts parallel to the glenoid, likely creating shear forces or limiting compressive forces. Pushing was less stable than pulling (all targets except sagittal 170 deg for both task types and horizontal 45 deg for bimanual) (p < 0.01), which is consistent with prior reports. For example, unimanual pushing at the 90 deg horizontal target was 197% less stable than unimanual pulling. There were limited stability benefits to task placement for pushing, and larger stability benefits may be seen from converting tasks from push to pull rather than optimizing task layout. There was no difference in stability between bimanual and unimanual tasks, suggesting no stability benefit to bimanual operation.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051007-051007-8. doi:10.1115/1.4043036.

Nerve guidance conduits (NGCs) are tubular tissue engineering scaffolds used for nerve regeneration. The poor mechanical properties and porosity have always compromised their performances for guiding and supporting axonal growth. Therefore, in order to improve the properties of NGCs, the computational design approach was adopted to investigate the effects of different NGC structural features on their various properties, and finally, design an ideal NGC with mechanical properties matching human nerves and high porosity and permeability. Three common NGC designs, namely hollow luminal, multichannel, and microgrooved, were chosen in this study. Simulations were conducted to study the mechanical properties and permeability. The results show that pore size is the most influential structural feature for NGC tensile modulus. Multichannel NGCs have higher mechanical strength but lower permeability compared to other designs. Square pores lead to higher permeability but lower mechanical strength than circular pores. The study finally selected an optimized hollow luminal NGC with a porosity of 71% and a tensile modulus of 8 MPa to achieve multiple design requirements. The use of computational design and optimization was shown to be promising in future NGC design and nerve tissue engineering research.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051008-051008-10. doi:10.1115/1.4043034.

Patients that undergo the arterial switch operation (ASO) to repair transposition of great arteries (TGA) can develop abnormal pulmonary trunk morphology with significant long-term complications. In this study, cardiovascular magnetic resonance was combined with computational fluid dynamics to investigate the impact of the postoperative layout on the pulmonary flow patterns. Three ASO patients were analyzed and compared to a volunteer control. Results showed the presence of anomalous shear layer instabilities, vortical and helical structures, and turbulent-like states in all patients, particularly as a consequence of the unnatural curvature of the pulmonary bifurcation. Streamlined, mostly laminar flow was instead found in the healthy subject. These findings shed light on the correlation between the post-ASO anatomy and the presence of altered flow features, and may be useful to improve surgical planning as well as the long-term care of TGA patients.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051009-051009-9. doi:10.1115/1.4043033.

The constitutive equation used to characterize and model spinal tissues can significantly influence the conclusions from experimental and computational studies. Therefore, researchers must make critical judgments regarding the balance of computational efficiency and predictive accuracy necessary for their purposes. The objective of this study is to quantitatively compare the fitting and prediction accuracy of linear viscoelastic (LV), quasi-linear viscoelastic (QLV), and (fully) nonlinear viscoelastic (NLV) modeling of spinal-cord-pia-arachnoid-construct (SCPC), isolated cord parenchyma, and isolated pia-arachnoid-complex (PAC) mechanics in order to better inform these judgements. Experimental data collected during dynamic cyclic testing of each tissue condition were used to fit each viscoelastic formulation. These fitted models were then used to predict independent experimental data from stress-relaxation testing. Relative fitting accuracy was found not to directly reflect relative predictive accuracy, emphasizing the need for material model validation through predictions of independent data. For the SCPC and isolated cord, the NLV formulation best predicted the mechanical response to arbitrary loading conditions, but required significantly greater computational run time. The mechanical response of the PAC under arbitrary loading conditions was best predicted by the QLV formulation.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051010-051010-15. doi:10.1115/1.4043031.
FREE TO VIEW

Many physiological systems involve strong interactions between fluids and solids, posing a significant challenge when modeling biomechanics. The objective of this study was to implement a fluid–structure interaction (FSI) solver in the free, open-source finite element code FEBio, that combined the existing solid mechanics and rigid body dynamics solver with a recently developed computational fluid dynamics (CFD) solver. A novel Galerkin-based finite element FSI formulation was introduced based on mixture theory, where the FSI domain was described as a mixture of fluid and solid constituents that have distinct motions. The mesh was defined on the solid domain, specialized to have zero mass, negligible stiffness, and zero frictional interactions with the fluid, whereas the fluid was modeled as isothermal and compressible. The mixture framework provided the foundation for evaluating material time derivatives in a material frame for the solid and in a spatial frame for the fluid. Similar to our recently reported CFD solver, our FSI formulation did not require stabilization methods to achieve good convergence, producing a compact set of equations and code implementation. The code was successfully verified against benchmark problems from the FSI literature and an analytical solution for squeeze-film lubrication. It was validated against experimental measurements of the flow rate in a peristaltic pump and illustrated using non-Newtonian blood flow through a bifurcated carotid artery with a thick arterial wall. The successful formulation and implementation of this FSI solver enhance the multiphysics modeling capabilities in febio relevant to the biomechanics and biophysics communities.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051011-051011-12. doi:10.1115/1.4043077.

Cardiac looping is an important embryonic developmental stage where the primitive heart tube (HT) twists into a configuration that more closely resembles the mature heart. Improper looping leads to congenital defects. Using the chick embryo as the experimental model, we study cardiac s-looping wherein the primitive ventricle, which lay superior to the atrium, now assumes its definitive position inferior to it. This process results in a heart loop that is no longer planar with the inflow and outflow tracts now lying in adjacent planes. We investigate the biomechanics of s-looping and use modeling to understand the nonlinear and time-variant morphogenetic shape changes. We developed physical and finite element models and validated the models using perturbation studies. The results from experiments and models show how force actuators such as bending of the embryonic dorsal wall (cervical flexure), rotation around the body axis (embryo torsion), and HT growth interact to produce the heart loop. Using model-based and experimental data, we present an improved hypothesis for early cardiac s-looping.

Commentary by Dr. Valentin Fuster
J Biomech Eng. 2019;141(5):051012-051012-8. doi:10.1115/1.4042665.

Significant advances in biomedical science often leverage powerful computational and experimental modeling platforms. We present a framework named physiology simulation coupled experiment (“PSCOPE”) that can capitalize on the strengths of both types of platforms in a single hybrid model. PSCOPE uses an iterative method to couple an in vitro mock circuit to a lumped-parameter numerical simulation of physiology, obtaining closed-loop feedback between the two. We first compared the results of Fontan graft obstruction scenarios modeled using both PSCOPE and an established multiscale computational fluid dynamics method; the normalized root-mean-square error values of important physiologic parameters were between 0.1% and 2.1%, confirming the fidelity of the PSCOPE framework. Next, we demonstrate an example application of PSCOPE to model a scenario beyond the current capabilities of multiscale computational methods—the implantation of a Jarvik 2000 blood pump for cavopulmonary support in the single-ventricle circulation; we found that the commercial Jarvik 2000 controller can be modified to produce a suitable rotor speed for augmenting cardiac output by approximately 20% while maintaining blood pressures within safe ranges. The unified modeling framework enables a testing environment which simultaneously operates a medical device and performs computational simulations of the resulting physiology, providing a tool for physically testing medical devices with simulated physiologic feedback.

Commentary by Dr. Valentin Fuster

Technical Brief

J Biomech Eng. 2019;141(5):054501-054501-7. doi:10.1115/1.4042899.

Incomplete stent apposition (ISA) is one of the causes leading to poststent complications, which can be found when an undersized or an underexpanded stent is deployed at lesions. The previous research efforts have focused on ISA in idealized coronary arterial geometry with circular cross section. However, arterial cross section eccentricity plays an important role in both location and severity of ISA. Computational fluid dynamics (CFD) simulations are carried out to systematically study the effects of ISA in arteries with elliptical cross section, as such stents are partially embedded on the minor axis sides of the ellipse and malapposed elsewhere. Overall, ISA leads to high time-averaged wall shear stress (TAWSS) at the proximal end of the stent and low TAWSS at the ISA transition region and the distal end. Shear rate depends on both malapposition distance and blood stream locations, which is found to be significantly higher at the inner stent surface than the outer surface. The proximal high shear rate signifies increasing possibility in platelet activation, when coupled with low TAWSS at the transition and distal regions which may indicate a nidus for in-stent thrombosis.

Commentary by Dr. Valentin Fuster

Errata

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In